#Qt sync tutorial mp4#
#Qt sync tutorial Bluetooth#

To protect against electrical shock, DO NOT immerse the cord or plugs or expose the electrical components to water or other liquid.Do not plug in the power cord or operate the appliance controls with wet hands. KEEP the power cord away from hot surfaces.KEEP the appliance and its power cord out of the reach of children when it is in operation or in the cooling down process.

Contact Customer Service using the information located on the back of this manual.

This appliance should be serviced ONLY by qualified service technicians.

Return appliance to an authorized service facility for examination, repair, or adjustment.

DO NOT operate any appliance if it has a damaged cord or plug, if it is not working properly, or if it has been damaged or dropped.

To avoid personal injury, NEVER place hands inside the appliance unless it is thoroughly cooled down.

While cooking, the internal temperature of the appliance reaches several hundred degrees Fahrenheit.

Doing so will prevent even cooking and may damage the appliance or cause it to overheat.

DO NOT cover the Air Intake Vent or Hot Air Outlet Vent while the appliance is operating.

To prevent food contact with the heating elements, do not overfill.

ALWAYS operate the appliance on a horizontal surface that is level, stable, and noncombustible with adequate space for airflow.

DO NOT place anything on top of the appliance.

When cooking, DO NOT place the appliance against a wall or within 5 inches of other appliances.

DO NOT place or use this appliance near water.

These sprays will build up on cookware and become difficult to remove while reducing the nonstick cooking performance.

WARNING: To reduce risk of electric shock, cook only using the removable containers trays, racks, etc.

DO NOT store any materials, other than manufacturer-recommended accessories, in this appliance when not in use.

Allow the appliance to cool and wipe excess oil and grease from the appliance.

Should the appliance emit black smoke, UNPLUG IMMEDIATELY and wait for smoking to stop before handling the appliance.

NEVER plug the appliance into an outlet below the surface where the appliance is placed.

MAKE SURE the appliance is properly plugged into a dedicated wall socket without any other appliances on the same outlet.

DO NOT plug in the power cord or operate the appliance controls with wet hands.

DO NOT place the appliance in any container or small confined space while the appliance is heated or in operation.

To disconnect, press the Power button to turn the appliance off, then remove the plug from the wall outlet.

ALWAYS attach the plug to the appliance first, then plug the cord into the wall outlet.

Close supervision is necessary when any appliance is used by or near children.

This appliance is not intended for use by children.

THIS APPLIANCE IS NOT INTENDED FOR use by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge unless they are under the supervision of a responsible person or have been given proper instruction in using the appliance.

DO NOT place the appliance on or near a hot gas or electric burner, or in a heated oven.

Do not reach into liquid if the appliance is plugged in and immersed. If the appliance falls or accidentally becomes immersed in water, unplug from wall outlet immediately.

NEVER immerse the main unit housing in water.

READ AND FOLLOW all instructions carefully.

Both amazing and unsurprising at the same time. Unless I'm missing something, the problem is with Apple/QuickTime.

#Qt sync tutorial mp4#

mp4 audio was already in sync when I imported it into a new project! mp4 into a new Screenflow project, detach the audio, bring it into sync in the project, note the number of frames/seconds, and then simply advance the audio by that amount in the original project. As a stop-gap fix, I figured I could just bring the exported.I'm thinking the problem is not with SF at all, but with Quicktime: Is there any way to fix this without the clumsy, trial-and-error method of intentionally making the audio lead the video in the project file by the same amount that it lags after export?

#Qt sync tutorial Bluetooth#

It doesn't appear to be a Bluetooth latency issue (I'm using wireless headphones), as it's fine in the project, and when using the internal speakers there is no difference. mov, but either way the lag is evident in the exported file. (So the lag does not get worse with time it's constant throughout.) In Screenflow project, the audio is perfectly in sync (using a detached audio track), but after I export it, it's off by about the same amount for the entire video. Hi there, I have a Zoom webinar recording that I've edited for YouTube, and the audio seems to lag in the file, exported file (viewed with QuickTime).